Does anyone know the tonnage (net and gross) for the purposes of registration of a C400 in Canada?

Hi I need is the service manual for the westerbeke 42b that explains how to remove and replace various components. I have looked on the westerbeke site and can’t locate a copy of it. Does anyone eithe

Hi all I need to replace my raw water pump on my westerbeke 42b (mark 1). I wanted see if anyone had a suggestion on where best place to source it other than westerbeke since they are a bit pricey Reg

Hi everybody, who's hull # 52? This is Allen #154. You stopped by and said hi while I was launching my tender in Glorietta Bay over the weekend (April 9). Always nice to meet a fellow 400 owner! - ALL

I’m getting ready to replace my original masthead sheaves with the Garhauer Ball-Bearing Sheaves. But Garhauer doesn’t sell a complete ‘kit’. Catalina Direct has a Masthead Rebuild Kit that includes t

Anyone want to help test the width of Garhauer Mast Head Sheaves? I can mail them to you with return postage, or you can have them at a discounted price. OR if someone has recently done a masthead she

Last spring I rubbed out and waxed the topsides and it made quite a difference in the boat's appearance. This spring, light gray stains start at the openings in the toe rail and streak down the top si

The Sparcraft website REALLY needs to be updated. While looking around, thou THIS page that has a summary of service, maintenance and tuning information.

Does anyone have any information on A/C Install for a 3 cabin? We have most of it planned, however, just working through confirming the exact mounting location, thru hull and pump locations etc. . Tha

I had a Catalina 400 a few years back. I had two AC Systems. One thru hull/strainer/pump was located in main bilge; the other thru hull was in bilge area just aft of engine compartment. I picked up mo

Hi all, As I sit in my cockpit at Stanley cay in the Bahamas this morning in bit of a blow I am trying to figure out a way fix what appears to be a problem with my headsail furler. As we were trying t

I think my starboard/aft motor mount needs replacing. It's very close to bottoming out on the forward arm. I did a shaft alignment today and that corner needed to come up a tad. Questions: Any tips fo

Looking for ideas on a new water pressure pump for 2006 MKII. Pump is under the galley sink above the water heater. Mine works fine but it is pretty loud and seems to be a pretty big draw on the batte

Anyone have any tricks to support the boom while changing the toggle? I was thinking about rigging some sort of support ‘loop’ and connecting it with a halyard. It also looks like I should disconnect

Hi I could use your help. I removed the raw water impeller and can’t get to pull any water from the intake. I don’t know if I installed the impeller backwards or something else is going on. This is on

Hi All, Sad to put our Snow Goose (1996 C400, Hull #51) on the market, but here is a spec sheet for anyone who may be interested or know of someone who is. VERY clean and sound. Call or email with que

All this recent talk about replacing hatches has got me wanting to buy some canvas hatch covers for my 1995 MkI (#36). I would've thought that you could buy a 'C400 Hatch Cover Set' but cannot find an

Is anyone aware of a MK2 for sale? I’m looking for one. Hope you don’t mind me asking. I had one I’m under contract and then found out the rudder shaft was bent. Covid messed up further plans but I st

Looking for some advice as I am sure many of you have had these hatch leaking issues. Finally figured out where some pesky leaks were originating and it seems that some of my Lewmar Hatches are leakin

"WAYPOINT" 1999 C400-2, 1999 has a Vetus throttle /shifter. We have been having problems with the red button getting stuck in the depressed position. I replaced it and it worked for only a short time.