[EXTERNAL] Re: [C400] Fridge replacement
This is great. How about writing an article for Catalina MAINSHEET Magazine?
?From: C400@Catalina400-445.groups.io <C400@Catalina400-445.groups.io>
On Behalf Of Paul Larter via groups.io
The fridge on Naia, 1999 build, started losing gas and thus not work in December last year. Naturally the timing was just before Christmas, the hottest time of the year when everyone goes on holiday here in Australia. A fridge unit of that age is not worth spending too much money on to repair, when the cost of a complete new unit is not all that much more. (Here in Oz anyway). So I looked for a replacement. To replace with a similar unit proved to be difficult as I couldn’t get pre-charged pipes of a sufficient length, 6.5 metres, to connect the compressor to the evaporator unit.
However, a local company, Ozefridge, could supply an electric eutectic unit made to measure, so I ordered one. You can look them up at https://www.ozefridge.com/ The setup I fitted has a 5 litre tank of 50% anti freeze in the fridge and a water and air cooled compressor in the aft lazarette
The tank fitted perfectly in a portrait position in the fridge. I had to make a new shelf, as the eutectic tank is much thinner than the old evaporator, so more room in the fridge.
The water cooling option uses the aft water tank as a heat sink in very hot conditions as well as air cooling. So far it has not been needed as by the time I had everything working, we had a Covid lockdown in the area where the boat is kept and by the time that was over, the weather had cooled down a bit.
Performance so far is excellent. The compressor is quiet and takes about 3 hours to take the tank from ambient temp. to minus 12 Celsius. from then on, it comes back on when the tank reaches minus 7 which takes hours. At night it doesn’t seem to switch on at all, but as soon as the sun hits the solar panel in the morning, a voltage sensor switches it on. There is a small computer fan in the fridge to circulate the cold air.
Beware if you replace a fridge unit. The 2 inch duct pipe for the copper piping from the compressor to the fridge is NOT one piece. There is a gap of about 700 mm or just over 2 feet where the aft hanging locker on the starboard side is. They are also not in line, with the aft duct lower than the forward one. I had to take out the floor of the locker to get the pipes through. You may not have to do this if you know what to expect, which I didn’t.
If anyone is interested in this project and would like more info. I’m happy to write more and give the details and pictures.
Naia C400 165
Frank's idea is a GREAT one! No pressure :-) but is there any way you could throw something together in the next day or so? The deadline for the next issue of Mainsheet is 6/10. I'd be happy to help as much as I can.
C400 Tech Editor
Hi Tom, it sounds like you need some notes for the magazine so I just took a couple of pictures of some of the ‘ improvements’ I have done on Sequel.....toggle quoted messageShow quoted text
Greetings from Vancouver. We have left as of June 1 for the summer cruising the B.C. coast till late September. I took some photos of some ‘improvements’ I have done on Sequel a MK1 1997 vintage.
First of all I had a pair of very sturdy rails made for each helm. These have eliminated the urge for people to grab the wheel while moving around the cockpit and are a location for handy drink holders.
I also had the stainless pushpit rail extended to the aft gate stantion. They are great for entering and exiting the boat and significantly stiffened the whole assembly.
I also had caps made for the deck at the transom just outboard of the aft cleats. These eliminate the wearing of the gel coat at these positions. I found that the wear was significant in this area and was in need of an expensive repair , again. Bonding these plates on with 5200 solved both issues, the cost of repair and the continued chafing. I am surprised that these boats do not have chocks in the rail for mooring lines from the factory.
These changes were made for a mere $800. Canadian and have made a big difference to Sequel.
Cheers Doug Burr
On Jun 8, 2021, at 1:09 PM, Tom Sokoloski <tomsoko@...> wrote:
Hi Frank and Tom, I’ll get onto it today and hopefully have something for you in time for the deadline.